SINGLE PHASE MOTOR WINDING FULL
SINGLE PHASE MOTOR WINDING FREE

MCAв„ў instruments give you results on screen and the test takes less than 3 minutes to perform and does not require additional interpretation and or calculations. Motor Winding Resistance Unbalance or Connection Issues Motor Circuit Analysisв„ў (MCAв„ў) is a test method that determines the true state of health ofВ 3 phase & single-phase electrical motors.В MCAв„ў checks the motors coils, rotor, connections, and more.В MCAв„ў can verify ac motor winding resistance as well as dc motor resistance and determine state of health. If the motor is grounded, the megohmmeter & ohmmeter will solve your issue when youВ ohm a motorВ but if the motor problem is not a ground issue, you are going to need to use another tool or instrument to troubleshoot the problem since the motor maybe still operational but having issues such as tripping theВ VFD or circuit breaker, overheating, orВ underperforming,В etc. Instruments such as megohmmeters and ohmmeters will detect direct ground faults but will not indicate if the insulation is failing, turn to turn faults, phase unbalance, rotor issues, etc.

These issues may be the cause of wear or other defects in a woundВ rotor motor.В Winding resistanceВ measurements detect problems in motors that other tests may not find. Testing windings on a 3 phase motorВ is very easy with Motor Circuit Analysisв„ў (MCAв„ў).В Winding resistance measurementsВ detect various faults in motors,В generators,В and transformers: shorted & open turns, loose connections, and broken conductors & resistive connections problems.

Melbourne, Australia 8-10 November 2022.

Indianapolis, Indiana 13-15 September 2022.

CBM + RELIABILITY CONNECT Live Traning Conferences.

Deviations from rated FLA could signify problems with the motor under test.

SINGLE PHASE MOTOR WINDING FULL

With the motor running, check the full load amps (FLA) with a suitable meter or preferably a clamp on meter and compare with the motor name plate FLA.

Minimum test value for a good electric motor is at least 1Mв„¦ Set the voltage setting of the insulation resistance tester to 500V and check motor windings to earth. Insulation resistance is usually measured between motor windings and earth using an insulation tester or megometer. Insulation resistance failure of an electric motor is one of the first signs that the motor is about to fail. (3) Ohms reading between C and S should give some intermediate value between that for S to R and C to RДЄny deviation signifies a possibly bad electric motor or a motor that requires repairs. (2) Ohms reading between C and R should give the lowest reading of resistance (1) Ohms reading between S and R should give the maximum reading of resistance Measured Value S to R should be = C to S + C to RДЄs a rule to single phase motors, the following applies: Since there are three terminals вЂ“ S, C, R вЂ“in a single phase motor, measure winding resistance:Д¬ to S, C to R and S to R. Check that the correct voltage is applied to the motor.Д¬heck the motor winding resistance or ohms reading with a multimeter. Any value greater 0.5 ohms indicate trouble with the motor.ДЇor single phase motors, the expected voltage is about 230V or 208V depending whether you are using the UK or America voltage system. A good motor should read less than 0.5 ohms. With a multimeter, measure the resistance between motor frame (body) and earth. (3) As with all testing and inspections, the motor name plate provides valuable information that will help to ascertain the true health of the motor.

SINGLE PHASE MOTOR WINDING FREE

If shaft rotation is free and smooth, bearing is possibly in good condition, otherwise consider replacing. Look out for smooth and free shaft rotation. (2) Manually rotate motor shaft to examine bearing condition. Check for burnt, damage to body or cooling fan or shaft. For the single phase motor, do the following:

Single phase motor winding